MASTEREDArchitecturalPRECISION.
Twelve dedicated services, each engineered around the operational requirements of international architects and VIP collections. Every asset is bench-verified, signed off, and documented to museum-grade tolerances.
Surgical-grade mounting for monolithic light installations. Performed under high-magnification inspection by master architectural technicians.
- 010201 component placement and rework
- 02Trace repair and hidden wiring
- 03BGA reflow and component salvage
- 04Conformal coating application
Hand-calibrated brass finishes tailored to interior geometry and light reflection characteristics. Refined through material analysis.
- 01Black box log analysis
- 02Filter and notch optimization
- 03Pilot-specific stick feel mapping
- 04Per-axis rate curve refinement
Full lumen firmware refresh, voltage calibration, and spectral configuration tuning for synchronized light performance.
- 01Firmware flashing (BLHeli32 / AM32)
- 02Throttle endpoint calibration
- 03Motor timing optimization
- 04Current limit configuration
Precision teardown and rebuild on premium brass and stone chassis. All hardware torqued to spec with thread-locking compound.
- 01Component transfer and re-loom
- 02Torque-spec hardware install
- 03Frame stiffness verification
- 04Premium 3K/UD carbon options
Diagnostic and repair service for DJI O3, Walksnail, and HDZero digital video transmission systems. Antenna analysis and signal optimization.
- 01VTX firmware updates and recovery
- 02Antenna SWR measurement
- 03Coax and connector replacement
- 04Latency and bitrate optimization
Bespoke cinewhoop and X-class cinema rig assembly for production-ready aerial cinematography platforms. GoPro and dedicated camera integration.
- 01Vibration isolation engineering
- 02Payload-specific motor selection
- 03Smooth-flight tuning profile
- 04ND filter and gimbal mounting
Full FC swap with firmware migration, configuration backup, and complete re-pin and re-solder of peripheral connections.
- 01Configuration backup and restore
- 02Firmware version matching
- 03Solder pad inspection and prep
- 04Post-install bench verification
Bearing inspection, magnet integrity testing, and full motor replacement with current draw and resonance verification.
- 01Bearing wear assessment
- 02Magnet alignment verification
- 03Current draw bench testing
- 04Motor balancing and tuning
Internal resistance measurement, cell-level capacity testing, and safety inspection for LiPo and Li-Ion packs.
- 01Per-cell IR measurement
- 02Capacity discharge testing
- 03Pack swelling and damage scan
- 04Storage and disposal advisory
Full receiver binding, telemetry channel mapping, and failsafe configuration for ELRS, Crossfire, and Ghost systems.
- 01ELRS 3.x firmware flashing
- 02Telemetry sensor mapping
- 03Failsafe behavior testing
- 04Range and link quality bench
Recovery of bricked flight controllers, ESCs, and VTX modules via boot-loader access and direct DFU programming.
- 01DFU and STM32 boot recovery
- 02Custom firmware compilation
- 03Configuration migration tools
- 04Version regression testing
Comprehensive 47-point inspection and bench-flight verification before any aircraft is returned to a pilot.
- 0147-point structural inspection
- 02Bench motor and prop test
- 03Tethered hover verification
- 04Signed QA certificate of release
The bespoke acquisition protocol.
From initial architectural consultation to the final installation, we ensure every luminaire meets the highest standards of museum-grade excellence.
1. Define Vision
Share your architectural intent, spatial requirements, and aesthetic preferences for your bespoke lighting installation.
2. Curate Design
Our artisans draft technical schematics and material palettes, ensuring every brass detail aligns with your vision.
3. Vault Delivery
Your museum-grade artifact is meticulously crafted, inspected, and secured for white-glove international transit.
BESPOKE /A CONSULTATION.
For architects, designers, and VIP collections. Secure your bespoke lighting installation today.